- 您现在的位置：买卖IC网 > Sheet目录1007 > S202S11 (Sharp Microelectronics)RELAY SSR 240VAC 8A TRIAC 4-SIP
S102S11 Series
S202S11 Series
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current at ON state
Input signal current at OFF state
I F (ON)
I F (OFF)
?
?
16
0
24
0.1
mA
mA
Output
Load supply voltage
Load supply current
S102S11
S202S11
V OUT (rms)
I OUT (rms)
?
?
80
80
0.1
120
240
I T (rms) × 80%( ? )
V
mA
Frequency
Operating temperature
f
T opr
?
?
47
? 20
63
80
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (l F ) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
For over voltage protection, a Varistor may be used.
A varistor used for the above mentioned scenarios should be located as close to the main output triac as
possible.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5N ? m.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device sur-
face.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
Silicone grease to be used is as follows;
1) There is no aged deterioration within the operating temperature ranges.
2) Base oil of grease is hardly separated and is hardly permeated in the device.
3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device.
Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.)
: G-747 (Shin-Etsu Chemical Co., Ltd.)
: SC102 (Dow Corning Toray Silicone Co., Ltd.)
In case the optional heat sink is screwed up, please solder after screwed.
Sheet No.: D4-A02801EN
8
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
S202S12
RELAY SSR 240VAC 8A ZC 4-SIP
S202T01
RELAY SSR 240VAC 2A TRIAC 4-SIP
S202TY1F
RELAY SSR 240VAC 2A TRIAC 4-SIP
S205TY2
RELAY SSR 240VAC 5A ZC 4-SIP
S208T02
RELAY SSR 240VAC 8A ZC 4-SIP
S212S01
RELAY SSR 240VAC 12A TRIAC 4-SIP
S216S01
RELAY SSR 240VAC 16A TRIAC 4-SIP
S216S02
RELAY SSR 240VAC 16A ZC 4-SIP
相关代理商/技术参数
S202S11F
功能描述:固态继电器-PCB安装 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
S202S12
功能描述:RELAY SSR 240VAC 8A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S202 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6
S202S12F
功能描述:固态继电器-PCB安装 4-SIP Zero Cross 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
S202SE1
功能描述:RELAY SSR 240VAC 8A TRIAC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S202 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6
S202SE1F
功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
S202SE2
功能描述:RELAY SSR 240VAC 8A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:S202 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6
S202SE2F
功能描述:固态继电器-PCB安装 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
S-202T
功能描述:稳流二极管 100V 2mA RoHS:否 制造商:Central Semiconductor 最大调节器电流:5.17 mA 最大极限电压:2.9 V 最大峰值工作电压:100 V 安装风格:Through Hole 封装 / 箱体:DO-204AH 封装: